고압 다이캐스팅의 열처리 Metallurgical and Materials Transactions A volume 38, pages2564–2574 (2007)Cite this article Abstract High-pressure die-cast Al alloys cannot normally be heated at high temperatures due to the presence of pores containing entrapped gases, which lead to the formation of surface blisters. It has been found that blistering can be avoided by using considerably shorter solution-treatment times
XixiDongaHailinYangbXiangzhenZhuaShouxunJiaShow moreAdd to MendeleyShareCite https://doi.org/10.1016/j.jallcom.2018.09.260Get rights and content Abstract A high strength (Yield strength ≥ 320 MPa) and high ductility (Tensile elongation ≥ 10%) die–cast aluminium alloy was first developed. The AlSiCuMgMn alloy processed by high pressure die casting can provide the high yield strength of 321 MPa, the high ultimate tensile strength of 425 MPa and the high ductility of 11.3%, after solution treated at
진공도가 알루미늄 다이캐스팅의 다공성과 기계적 성질에 미치는 영향 Author links open overlay panelHanxueCaoabMengyaoHaoaChaoShenaPengLiangaShow moreAdd to MendeleyShareCite https://doi.org/10.1016/j.vacuum.2017.09.048Get rights and content Abstract AlSi9Cu3 alloy castings were produced by the vacuum-assisted high pressure die casting (HPDC) process under three different absolute pressures: 500 mbar, 200 mbar and 100 mbar. The influence of absolute pressure in the die cavity on the porosity, microstructure
HailinYangabShouxunJiaZhongyunFanaShow moreAdd to MendeleyShareCite https://doi.org/10.1016/j.matdes.2015.07.074Get rights and content Highlights • Solution and ageing significantly improve the tensile strength of die-cast Al–Si–Cu alloy. • Low Fe is necessary for improving the ductility in the solution and aged alloy. • Cu-rich phase is dissolved during solutionising of die-cast Al–Si–Cu alloy. • θ′ and Q′ precipitates co-exist in
Zheng Chen, Suo Fan, Lei Peng, Yincheng Wang, Xiaolong Gong, Xinwang Liu & Zitian Fan International Journal of Metalcasting (2022)Cite this article 67 Accesses Metricsdetails Abstract This paper presents a novel process for preparing high-strength water-soluble salt cores with complex structure via layered extrusion forming using K2SO4 and KCl as the base salt materials, which is suitable for manufacturing
Xiaolong Gong, Xiongjie Xiao, Xinwang Liu & Zitian Fan Received 03 Apr 2022, Accepted 21 Apr 2022, Published online: 13 May 2022 Download citation https://doi.org/10.1080/10426914.2022.2072887 CrossMark ABSTRACT In this work, the high-strength composite salt cores reinforced by corundum powder were successfully prepared using 30 mol% Na2SO4 +70 mol% NaCl as the matrix materials, which can be used to fabricate
Author links open overlay panelAndreasSchillingDanielSchmidtJakobGlückNiklasSchwenkeHusamSharabiMartinFehlbierShow moreAdd to MendeleyShareCite https://doi.org/10.1016/j.simpat.2022.102585Get rights and content Under a Creative Commons license Open access Abstract In this work, a simulations study on the impact on gravity cast salt cores was carried out for the different casting parameters in high pressure die casting as well as in rheocasting. To compare the simulation results, salt cores were
Xue-ting Wang, Wei-hua Liu, Xuan-yu Liu & Lai Song International Journal of Metalcasting (2022)Cite this article 84 Accesses 1 Citations Metricsdetails Abstract In this paper, the interfacial energy of various inorganic salts was calculated using the first principle. Finally, NaCl and Na2SO4 were determined as the core materials. A high-strength composite salt core was prepared by optimizing the distribution ratio
Xiaolong Gong, Wenming Jiang , Fuchu Liu, Zhiyuan Yang, Feng Guan, and Zitian FanState Key Laboratory of Materials Processing and Die and Mould Technology, Huazhong University of Science andTechnology, Wuhan 430074, China Copyright 2020 American Foundry Societyhttps://doi.org/10.1007/s40962-020-00480-9 Abstract The water-soluble salt core with higher bending strength and toughness is necessary to withstand the high pressure
A.HamasaiidaG.DouraT.LouloucM.S.DarguschbaUniversité de Toulouse, INSA, UPS, Mines Albi, ISAE, ICA (Institut Clément Ader), CROMeP, Campus Jarlard, F-81013 Albi Cedex 09, FrancebCAST Cooperative Research Centre, School of Engineering, The University of Queensland, St. Lucia, Brisbane QLD 4072, AustraliacUniversité de Bretagne-Sud, LIMAT B, rue de Saint-Maudé, 56321 Lorient, France Abstract An analytical model is proposed to predict the
