Tag Archives: High pressure die casting

Fig 7: Simulated results for 100S rotor for filling time

Thermal Factor of Aluminium High pressure Die Casting Container (Mould) to achieve Six Sigma Quality of Castings

This introductory paper is the research content of the paper “Thermal Factor of Aluminium High pressure Die Casting Container (Mould) to achieve Six Sigma Quality of Castings” published by IJERT. 1. Overview: 2. Abstract This paper deals with the analysis of the temperature factors of aluminium high pressure die casting Container (mould). It also describes

Read More

Fig. 3. Photographs of the die cast trial product of a reaction shaft support.

A Feasibility Study of the Partial Squeeze and Vacuum Die Casting Process

This article introduces the paper “A feasibility study of the partial squeeze and vacuum die casting process”. 1. Overview: 2. Research Background: The manufacturing of aluminum alloys is increasingly important due to demands for lightweight materials, improved functionality, higher quality, and environmentally friendly production techniques [1–3]. Die casting offers speed and precision but suffers from

Read More

Effects of microstructure and casting defects on the fatigue behavior of the high-pressure die-cast AlSi9Cu3(Fe) alloy

Effects of microstructure and casting defects on the fatigue behavior of the high-pressure die-cast AlSi9Cu3(Fe) alloy

This article introduces the paper [‘Effects of microstructure and casting defects on the fatigue behavior of the high-pressure die-cast AlSi9Cu3(Fe) alloy’] presented at the [‘Procedia Structural Integrity’] 1. Overview: 2. Research Background: Background of the Research Topic: High-pressure die-cast (HPDC) components are increasingly utilized due to their “good flexibility and high productivity”, making them suitable

Read More

Figure 1 Bar permanent casting

PROMISING CASTING ALUMINUM ALLOYS WITHOUT REQUIREMENT FOR HEAT TREATMENT

This introductory paper is the research content of the paper [“‘PROMISING CASTING ALUMINUM ALLOYS WITHOUT REQUIREMENT FOR HEAT TREATMENT'”] published by [‘METAL 2019 Conference Proceedings’]. 1. Overview: 2. Abstract Three kinds of aluminum alloys based on Al-Zn-Mg system and doped with Ca, Ni and Ce were studied. Determination of hot tearing tendency, phase composition and

Read More

igure 11. A short-shot experiment by using the double PIG-nozzle units for PIG die-casting. (a) Aluminum melt flow into the rectangular die cavity, (b) solidified aluminum melts

Manufacturing of Aluminum Alloy Parts from Recycled Feedstock by PIG Die-Casting and Hot Stamping

This introductory paper is the research content of the paper [“Manufacturing of Aluminum Alloy Parts from Recycled Feedstock by PIG Die-Casting and Hot Stamping”] published by [MDPI]. 1. Overview: 2. Abstract PIG (Pin-Injection-Gate) die-casting and hot stamping was developed for fabrication of small-sized and thin-walled aluminum alloy parts from the recycled feedstock. The pure aluminum

Read More

Figure 1. Network layout and technology stack from the HDPC cell to the storage solution

Towards a Data Lake for High Pressure Die Casting

This introductory paper is the research content of the paper “Towards a Data Lake for High Pressure Die Casting” published by MDPI. 1. Overview: 2. Abstract The High Pressure Die Casting (HPDC) process is characterized by a high degree of automation and therefore represents a data rich production technology. From concepts such as Industry 4.0

Read More

Source: VAW AP

Die Casting Technology: A Comprehensive Overview (Die Casting Automotive Body Components Handbook)

This paper introduction was written based on the “THE Aluminium Automotive MANUAL Manufacturing – Casting methods” published by the European Aluminium Association. Introduction This document provides an overview of various casting methods, with a focus on their applications in the automotive industry. It covers a range of techniques from traditional sand casting to more advanced

Read More

Figure 3.2: Shrinkage and porosity defect

Study of Process Parameters in High Pressure Die Casting

This introductory paper is the research content of the paper “Study of Process Parameters in High Pressure Die Casting” published by International Journal of Science and Research (IJSR). 1. Overview: 2. Abstract A study has been carried out for the die casting process parameters in order to achieve the improved quality of high pressure die

Read More

Figure 4-7. Cooling system of the 3D printed sliders

INNOVATIVE COOLING SOLUTIONS OF HPDC TECHNOLOGY

This introductory paper is the research content of the paper [“INNOVATIVE COOLING SOLUTIONS OF HPDC TECHNOLOGY”] published by [Multidiszciplináris Tudományok]. 1. Overview: 2. Abstract In High Pressure Die Casting (HPDC), the so-called sliders are moving components of the mould, that can form cavities, holes, and undercuts. Sliders differ greatly from fixed- and moving mould halves

Read More

Figure 2. Three-phase injection system.

Injection Parameters Setting in High-Pressure Die Casting

This introductory paper is the research content of the paper “Injection Parameters Setting in High-Pressure Die Casting” published by STM Journals. 1. Overview: 2. Abstract The advancement of science and processing technology is highly essential. Aluminium die-cast components are widely used. Proper process parameters are required. This paper studies optimum injection parameters. The common defects

Read More