Tag Archives: Applications

Figure 2.1: Rotor test setup for measurements of inter-bar resistance.

Analysis and Reduction of Parasitic Effects in Induction Motors With Die-Cast Rotors

This introduction paper is based on the Doctoral Thesis “Analysis and Reduction of Parasitic Effects in Induction Motors With Die-Cast Rotors” published by “KTH Royal Institute of Technology”. 1. Overview: 2. Abstract: This thesis presents a study of inter-bar current effects on induction motors with die-cast aluminium and die-cast copper rotors. The parasitic effects introduced

Read More

Fig. 1 Schematic representation of experimental apparatus

JIS ADC12 Aluminum Alloy Semi-Solid Slurry Preparation Technology by Applying Mechanical Vibration

This introduction paper is based on the paper “[JIS ADC12 Aluminum Alloy Semi-Solid Slurry Preparation Technology by Applying Mechanical Vibration]” published by “[Materials Transactions]”. 1. Overview: 2. Abstract: Semi-solid high pressure die casting is known as a process capable of forming high quality products. JIS ADC12 aluminum alloy is widely used for high pressure die

Read More

Figure 5: Laser marked identifier on aluminum die casting alloy.

Review of technologies for identification of die casting parts

The content of this introduction paper is based on the article “Review of technologies for identification of die casting parts” originating from researchers affiliated with Laserax Inc., Université Laval, and Viami International. 1. Overview: 2. Abstract: Part traceability is increasingly required not only for safety critical applications, but for a growing number of applications within

Read More

Figure 1: Change of the mechanical properties of the three magnesium alloys (left) and fatigue strength increase of AS 31 (right) due to Vacural® die casting

Mechanical properties and fatigue behaviour of magnesium alloys for castingsused in e-mobility applications based on different casting processes

M. Schütze1, J. Ganzenmüller2, M. Becker3, C. Mangos1, G. Piazza2, L. Kallien1, E. Beeh21Aalen University; 2German Aerospace Center (DLR), Stuttgart; 3Oskar Frech GmbH + Co. KG, Schorndorf The industrial shift towards e-mobility is an opportunity for the economic production of high pressuredie castings (HPDC) components, such as motor housings, gearboxes and covers. Those parts are

Read More

Figure 1. schematic views of; a) vertical; b) horizontal and c) curved die chill casting processes

Data Models for Casting Processes – Performances, Validations and Challenges

This introduction paper is based on the paper “Data Models for Casting Processes – Performances, Validations and Challenges” published by “IOP Publishing”. 1. Overview: 2. Abstract: Data-driven models with their associated data learning and training schemes can be utilised for the light metal casting processes. This paper presents the basis of data model building processes

Read More

Figure 1. Systematic workflow to analyze datasets, preprocessing, selecting models, and evaluating them to improve die-casting part classification systems.

Improving Die-Casting Part Classification using Transfer Learning with Deep Convolutional Neural Networks

This introduction paper is based on the paper “Improving Die-Casting Part Classification using Transfer Learning with Deep Convolutional Neural Networks” published by “IEOM Society International”. 1. Overview: 2. Abstract: Product quality is a crucial factor in the manufacturing process today, as it determines the company’s competitive advantages and the consumer’s requirements. The problem arises from

Read More

Fig.1 Die casting specimens

Effects of Trace Variation of Al Content on Microstructure and Properties of HPDC Mg-4Sm-2Al Alloy

This introduction paper is based on the paper “Effects of Trace Variation of Al Content on Microstructure and Properties of HPDC Mg-4Sm-2Al Alloy” published by “Special Casting & Nonferrous Alloys”. 1. Overview: 2. Abstract: SA42 and Mg-4Sm-2.6Al (SA42.6) alloys were fabricated by HPDC process, and influence of trace Al content on mechanical properties was systematically

Read More

Figure 1 A typical structure of CPU package and heat sink module.

Challenges in Cooling Design of CPU Packages for High-Performance Servers

This introduction paper is based on the paper “Challenges in Cooling Design of CPU Packages for High-Performance Servers” published by “Heat Transfer Engineering”. 1. Overview: 2. Abstract: Cooling technologies that address high-density and asymmetric heat dissipation in CPU packages of high-performance servers are discussed. Thermal management schemes and the development of associated technologies are reviewed

Read More

Fig. 1. TiN- and Ti(B,N)-coated core with the corresponding cast.

Application of wear-resistant PACVD coatings in aluminium diecasting: economical and ecological aspects

This introduction paper is based on the paper “Application of wear-resistant PACVD coatings in aluminium diecasting: economical and ecological aspects” published by “Surface and Coatings Technology”. 1. Overview: 2. Abstract: One of the major manufacturing techniques for aluminium precision parts is the pressure diecasting process. However, nowadays the state of the art involves the application

Read More

Fig. 4 - Porosity identify by a) X-ray on components from the first experimental activity, b) FEM simulations, c) X-ray on components from the final experimental activity (optimization of process parameters)

Numerical and experimental analysis of a high pressure die casting Aluminum suspension cross beam for light commercial vehicles

This introduction paper is based on the paper “Numerical and experimental analysis of a high pressure die casting Aluminum suspension cross beam for light commercial vehicles” published by “La Metallurgia Italiana”. 1. Overview: 2. Abstract: The purpose of the present paper is to enhance and deepen the lightweight optimization in automotive, in particular for commercial

Read More