Duoc T Phan, Syed H Masood*, Syed H Riza, and Harsh ModiDepartment of Mechanical and Product Design Engineering, Swinburne University of Technology, Hawthorn, Melbourne, Australia*Email: smasood@swin.edu.au Abstract In High Pressure Die Casting (HDPC) process, chill vents are used to allow residual air and gases to exhaust out from the mould cavity. The objective of this
Xiaoke Li, Gaohui Li, Jun Ma, Yang Cao, Yapeng Xu, Wuyi MingShow moreAdd to MendeleyShareCite https://doi.org/10.1016/j.jmapro.2024.03.022Get rights and content Highlights Abstract Metallic glasses (MGs), also known as amorphous alloys, has a unique atomic structure with long-range disorder and short-range order. MGs has excellent mechanical properties and is favored by many industries, such as, aerospace, medical devices, electronics and electricity, sports and leisure, etc. However, large-size MGs
by Dirk Lehmhus Fraunhofer Institute for Manufacturing Technology and Advanced Materials IFAM, Wiener Straße 12, 28359 Bremen, GermanyMetals 2024, 14(3), 334; https://doi.org/10.3390/met14030334Submission received: 25 February 2024 / Accepted: 8 March 2024 / Published: 14 March 2024(This article belongs to the Special Issue Advances in Metal Casting Technology) 1. Introduction It is a platitude that science and technology do not necessarily evolve along straight paths.
Yu-Tong Yang, Zhong-Yuan Qiu, Zhen Zheng, Liang-Xi Pu, Ding-Ding Chen, Jiang Zheng, Rui-Jie Zhang, Bo Zhang & Shi-Yao Huang Abstract High-pressure die casting (HPDC) is one of the most popular mass production processes in the automotive industry owing to its capability for part consolidation. However, the nonuniform distribution of mechanical properties in large-sized HPDC products adds complexity to part property evaluation. Therefore, a methodology
Yiwu Xu ab1, Yuxin Zhang c1, Jinping Li d, Pan Wang e, Jianfeng Wang e, Houwen Chen c, Houqing Sun f, Hongyi Zhan e Abstract Chromium (Cr) is rarely added to Al–Si die cast alloys as it has a strong tendency to induce the formation of coarse-sized sludge particles. In the present study, high pressure die-cast samples made of Al-7wt.%Si–Cr–Mg alloys with varied Fe contents (0.11 wt%, 0.26 wt% and 0.32 wt%) were tensile tested under as-cast and T5 heat-treated conditions, in comparison
Jingkai Zhang1, Yang Li1, Lai Song1, Weihua Liu1 & Xue Zou1 Abstract This study analyzes the effects of different pouring temperatures and mold temperatures on the crack behavior of NaCl–Na2SO4 composite water-soluble salt cores (WSSC). Firstly, calculate the solid fraction during the solidification process of the salt core using the Newton baseline method. Then predict the sensitivity of the salt core
Janette Brezinová1,* , Miroslav Džupon 2, Viktor Puchý2, Jakub Brezina 3, Pavlo Maruschak 4,Anna Guzanová3, Lýdia Sobotová5 and Miroslav Badida 5 Abstract This paper presents the results of research focused on increasing the lifespan of HPDCmoulds for casting aluminium alloys by applying duplex PVD coatings in combination with lasertexturing the base material before the coatings’
Yiwu Xu ab1, Yuxin Zhang c1, Jinping Li d, Pan Wang e, Jianfeng Wang e, Houwen Chen c, Houqing Sun f, Hongyi Zhan e Abstract Chromium (Cr) is rarely added to Al–Si die cast alloys as it has a strong tendency to induce the formation of coarse-sized sludge particles. In the present study, high pressure die-cast samples made of Al-7wt.%Si–Cr–Mg alloys with varied Fe contents (0.11 wt%, 0.26 wt% and 0.32 wt%) were tensile tested under as-cast and T5 heat-treated conditions, in comparison
Benjamin E. MacDonald1, Stuart Wiesner2, Ryan Holdsworth1, Carl Söderhjelm1 & Diran ApelianORCID:orcid.org/0000-0001-9743-606X1 Abstract The effects on phase equilibria of La and Fe additions to the Al–Ce–Ni-based alloy system are explored under high-pressure die casting conditions. The addition of La to Al–Ce–Ni-based alloy system only reacts with Ce synergistically to promote the formation of the Al11(Ce,La)3 intermetallic phase as predicted by CALculation
X.Y. Jiao ab, P.Y. Wang c, Y.X. Liu d, W.N. Liu e, A.X. Wan d, L.J. Shi c, C.G. Wang c, S.M. Xiong dShow moreAdd to MendeleyShareCite https://doi.org/10.1016/j.matlet.2024.136045Get rights and content Abstract The effective methods to regulating porosity and externally solidified crystals (ESCs) have been remained as a challenging task for high pressure die casting (HPDC) automobile parts. In this work, a newly designed ceramic shot sleeve is proposed for reducing porosity and optimizing ESCs. As a result, both porosity
