Tag Archives: ADC12

Figure 1. Typical applications of aluminium castings in automotive vehicles [5]. Nemak/American Metal Market Conference, 2015, accessed on 1 October 2022.

Joining Technologies for Aluminium Castings—A Review

This introduction paper is based on the paper “Joining Technologies for Aluminium Castings—A Review” published by “Coatings”. 1. Overview: 2. Abstract: Aluminium castings have been widely used in many industries, including automotive, aerospace, telecommunication, construction, consumer products, etc., due to their lightweight, good electric and thermal conductivity, and electromagnetic interference/radio frequency interference (EMI/RFI) shielding properties.

Read More

FIGURE 3.—Microstructure of specimens formed by varying injection pressure: (a) 60 MPa, (b) 80 MPa, (c) 100MPa, (d) 125MPa. Brighter regions are a-Al grains and the darker regions are a mixture of empty and [Al þ Mg2Si] eutectic regions.

Injection Parameters Optimization and Artificial Aging of Automotive Die Cast Aluminum Alloy

This introduction paper is based on the paper “Injection Parameters Optimization and Artificial Aging of Automotive Die Cast Aluminum Alloy” published by “Materials and Manufacturing Processes”. 1. Overview: 2. Abstract: High-pressure die castings are expected to be used in the near future as high-duty structural components in the automotive industry. The effects of die casting

Read More

Figure 1. Photograph of the base microstructure of the SSM-ADC12 aluminum alloy formed using GISS casting

The Mechanical Properties of a Transient Liquid Phase Diffusion Bonded SSM-ADC12 Aluminum Alloy with a ZnAl4Cu3 Zinc Alloy Interlayer

This introduction paper is based on the paper “The Mechanical Properties of a Transient Liquid Phase Diffusion Bonded SSM-ADC12 Aluminum Alloy with a ZnAl4Cu3 Zinc Alloy Interlayer” published by “Journal of Manufacturing and Materials Processing (MDPI)”. 1. Overview: 2. Abstract: In this study, the mechanical properties of SSM-ADC12 aluminum alloy specimens with a ZnAl4Cu3 zinc

Read More

Fig. 1 – Eutectic solidification region of a cooling curve and its first derivative and related thermal parameters

Influence of Mg and Ti on both eutectic solidification and modifying efficiency in Sr-modified Al-7Si cast alloys

This introduction paper is based on the paper “Influence of Mg and Ti on both eutectic solidification and modifying efficiency in Sr-modified Al-7Si cast alloys” published by “La Metallurgia Italiana”. 1. Overview: 2. Abstract: Magnesium and titanium are the main alloying elements always present in a commercial A356 alloy, and strontium is commonly added to

Read More

Fig. 1 Schematic representation of experimental apparatus

JIS ADC12 Aluminum Alloy Semi-Solid Slurry Preparation Technology by Applying Mechanical Vibration

This introduction paper is based on the paper “[JIS ADC12 Aluminum Alloy Semi-Solid Slurry Preparation Technology by Applying Mechanical Vibration]” published by “[Materials Transactions]”. 1. Overview: 2. Abstract: Semi-solid high pressure die casting is known as a process capable of forming high quality products. JIS ADC12 aluminum alloy is widely used for high pressure die

Read More

Figure 1. Schematic diagram of a typical HPDC process.

Development of High Performance Copper Alloy Chill Vent for High Pressure Die Casting

This introductory paper is the research content of the paper [“Development of High Performance Copper Alloy Chill Vent for High Pressure Die Casting”] published by [‘International Journal of Mechanical Engineering and Robotics Research’]. 1. Overview: 2. Abstracts / Introduction In High Pressure Die Casting (HPDC), chill vents are crucial for removing residual air and gases

Read More

Fig.4 Grain orientation and grain boundary distribution at position A under different cooling rates

Effects of Cooling Rate on Solidification Structure and Performance of ADC12 Alloy

This introductory paper is the research content of the paper [“Effects of Cooling Rate on Solidification Structure and Performance of ADC12 Alloy”] published by [Special Casting & Nonferrous Alloys]. 1. Overview: 2. Abstracts / Introduction Abstract: Effects of cooling rate on solidification structure evolution and mechanical properties of ADC12 aluminum alloy were investigated through directional

Read More

Fig. 7. Appearance of coated core-pins after 18 shots. The geometry of a pin is 8 mm diameter with 10 mm height. Severe soldered parts and the most slightly soldered part around a pin are shown.

Evaluation of Soldering on Surface-Treated Specimens with both Actual Die Casting and Dipping Test into Molten Al Alloy

This article introduces the paper [“Evaluation of Soldering on Surface-Treated Specimens with both Actual Die Casting and Dipping Test into Molten Al Alloy”] published by [電気製鋼 (The Iron and Steel Institute of Japan)]. 1. Overview: 2. Abstracts or Introduction This paper investigates the soldering behavior of surface coatings in both die casting and dipping tests.

Read More

Fig. 1. Distribution of Fe and Al at soldering part. Fe/Al compound layer is observed.

Prediction and Evaluation of Ejecting Stress Distribution at Die Surface of Die-Casting through Numerical Analyses

This article introduces the paper [“Prediction and Evaluation of Ejecting Stress Distribution at Die Surface of Die-Casting through Numerical Analyses”] published by [‘電気製鋼’]. 1. Overview: 2. Abstracts or Introduction In die casting, molten metal such as aluminum alloy is injected into a die cavity at high speed and solidified rapidly to efficiently produce complex shaped

Read More

Figure 2 Die dimension design of bicycle pedal forming and the final product [34].

Advancements in surface treatments for aluminum alloys in sports equipment

This article introduces the paper [‘Advancements in surface treatments for aluminum alloys in sports equipment’] presented at the [‘Reviews on Advanced Materials Science’] 1. Overview: 2. Research Background: Background of the Research Topic: Aluminum alloys are widely used in sports equipment due to their “exceptional properties, such as a high strength-to-weight ratio, good formability, and

Read More