This article introduces the paper “Analysis of Magnesium Addition, Hydrogen Porosity and T6 Heat Treatment Effects on Mechanical and Microstructural Properties of Pressure Die Cast 7075 Aluminum Alloy” presented at the THE GRADUATE SCHOOL OF NATURAL AND APPLIED SCIENCES OF MIDDLE EAST TECHNICAL UNIVERSITY 1. Overview: 2. Research Background: 3. Research Purpose and Research Questions:
This article introduces the paper “Cooling Performance of LED Head Lamp with Heat Sink and Cooling Fan”. 1. Overview: 2. Research Background: The increasing use of LEDs in automotive lighting systems presents a challenge due to heat generation from high-power LEDs, leading to performance degradation and reduced lifespan. Previous research identified factors affecting LED lifespan
This article introduces the paper [‘Advancements in surface treatments for aluminum alloys in sports equipment’] presented at the [‘Reviews on Advanced Materials Science’] 1. Overview: 2. Research Background: Background of the Research Topic: Aluminum alloys are widely used in sports equipment due to their “exceptional properties, such as a high strength-to-weight ratio, good formability, and
This article introduces the paper “A review of air-cooling battery thermal management systems for electric and hybrid electric vehicles”. 1. Overview: 2. Background: The paper begins by highlighting the increasing concentration of greenhouse gases (GHGs) since the 1900s, primarily due to the combustion of fossil fuels in internal combustion engines (ICEs). Transportation is a significant
This article introduces the paper “A novel automated heat-pipe cooling device for high-power LEDs”. 1. Overview: 2. Research Background: High-power LEDs are increasingly popular in various applications, offering advantages like long lifespan, high reliability, low energy consumption, fast response time, and color variability. However, their efficiency (15-25% power-to-light conversion) is limited, with over 80% of
This article introduces the paper [‘Mg Casting Alloys for the Aerospace Challenge’] presented at the [‘JOURNAL OF METALS’] 1. Overview: 2. Research Background: Background of the Research Topic: The utilization of magnesium alloys in aerospace applications has been driven by their inherent advantages, coupled with continuous advancements in alloy development and foundry practices. Initially a
This article introduces the paper [‘Mold structure design and casting simulation of the high-pressure die casting for aluminum automotive clutch housing manufacturing’] presented at the [‘Int J Adv Manuf Technol’] 1. Overview: 2. Research Background: Background of the Research Topic: The demand for aluminum die casting products has seen a continuous increase since Doehle’s initial
This article introduces the paper “AUTOMOTIVE APPLICATIONS OF MAGNESIUM AND ITS ALLOYS”. 1. Overview: 2. Research Background: 3. Research Objectives and Research Questions: 4. Research Methodology: 5. Main Research Findings: 6. Conclusion and Discussion: 7. Future Research Directions: 8. References: 9. Copyright: This material is based on the paper: AUTOMOTIVE APPLICATIONS OF MAGNESIUM AND ITS
This article introduces the paper [‘The Impact of Increased Recycle Content on Microstructure, Tensile Properties and Hemming Capability in Automotive Al-Mg-Si Alloys’] submitted to the [‘University of Pittsburgh’] 1. Overview: 2. Research Background: Background of the Research Topic: The automotive industry’s trend towards mass aluminization, starting in the mid-to-late 1980s, has led to increased use
This paper summary is based on the article [‘The Future of Structural Components in HPDC.’] presented at the [‘Bühler AG’] 1. Overview: 2. Abstracts The continuing quest for lighter-weight components in the automotive industry hasseen the emergence of a lucrative new market for die casting: structural components.The demand for these large, complex components, such as
![Figure 2. The Binary Phase Diagram of Al-Zn Alloy [1].](https://castman.co.kr/wp-content/uploads/image-426-527x342.webp)
![Figure 2 Die dimension design of bicycle pedal forming and the final product [34].](https://castman.co.kr/wp-content/uploads/image-526-570x342.webp)
![Fig. 5. Double silica cooling structure with copper meshes (Ref. [186]).](https://castman.co.kr/wp-content/uploads/Fig.-5.-Double-silica-cooling-structure-with-copper-meshes-Ref.-186-570x342.webp)
