This article introduces the paper ‘A review of heat pipe application including new opportunities’ published by ‘Frontiers in Heat Pipes’. 1. Overview: 2. Abstracts or Introduction This paper provides a detailed review of heat pipe applications, spanning from computer electronics to renewable energy systems. In the realm of computer electronics, the escalating performance and power
![Fig. 5. Double silica cooling structure with copper meshes (Ref. [186]).](https://castman.co.kr/wp-content/uploads/Fig.-5.-Double-silica-cooling-structure-with-copper-meshes-Ref.-186-570x342.webp)
This article introduces the paper “A review of air-cooling battery thermal management systems for electric and hybrid electric vehicles”. 1. Overview: 2. Background: The paper begins by highlighting the increasing concentration of greenhouse gases (GHGs) since the 1900s, primarily due to the combustion of fossil fuels in internal combustion engines (ICEs). Transportation is a significant
This article introduces the paper “Advanced Thermal Management for High-Power ICs: Optimizing Heatsink and Airflow Design” presented at the Applied Sciences (MDPI) 1. Overview: 2. Research Background: 3. Research Purpose and Research Questions: 4. Research Methodology 5. Main Research Results: 6. Conclusion and Discussion: 7. Future Follow-up Research: 8. References: 9. Copyright: This material was
This article introduces the paper “Heat treatment impact on the structure of die-cast magnesium alloys” published in the Journal of Achievements in Materials and Manufacturing Engineering in 2007. 1. Overview: 2. Research Background: 3. Research Purpose and Research Questions: 4. Research Methodology: 5. Major Research Findings: 6. Conclusion and Discussion: 7. Future Follow-up Research: 8.
This article introduces the paper “Three-Phase 75 kW Brushless Direct Current Motor for Electric Vehicles: Different Power Stage Design, Calculation of Losses, Cooling Techniques, and Comparison”. 1. Overview: 2. Research Background: The increasing need to reduce CO2 and SO2 emissions due to climate change necessitates improvements in electric vehicle efficiency. While Brushless Direct Current (BLDC)
This article introduces the paper “Heat Dissipation Design of High Power LED Headlamp”. 1. Overview: 2. Background: High-brightness white light-emitting diodes (LEDs) are very promising in many new illumination applications. LED light sources offer advantages such as long lifespan, fast response speed, environmental friendliness (mercury-free), and a color temperature (5500K-6000K) closer to natural light than
This article introduces the paper “Design of gravity assisted heat exchanger and its application on enhanced waste heat recuperation utilizing organic Rankine and LNG system”. 1. Overview: 2. Research Background: The research addresses the growing global energy demand, projected to increase by 33% by 2050 [1]. A significant portion of energy is wasted as low-grade
This article introduces the paper “Design and Manufacturing of High Performance, Reduced Charge Heat Exchangers”. 1. Overview: 2. Background: Heating, ventilation, air-conditioning, and refrigeration (HVAC&R) systems consume a significant portion of residential and commercial building energy. Reducing refrigerant charge to mitigate greenhouse gas emissions is a crucial objective. Traditional heat exchangers (HXs) using round tubes
Imran Zahid ab, M. Farhan a, M. Farooq a, M. Asim a, M. Imran c Abstract Electronic devices are being used extensively for different applications, where the thermal management of these devices is still a critical challenge due to rapid miniaturization, high heat flux and constantly rising temperature. Phase change materials (PCMs) based thermal management is adopted, but the low thermal conductivity limits their use in temperature-controlled electronic devices. Nano-enhanced phase change materials
Benjamin E. MacDonald1, Stuart Wiesner2, Ryan Holdsworth1, Carl Söderhjelm1 & Diran ApelianORCID:orcid.org/0000-0001-9743-606X1 Abstract The effects on phase equilibria of La and Fe additions to the Al–Ce–Ni-based alloy system are explored under high-pressure die casting conditions. The addition of La to Al–Ce–Ni-based alloy system only reacts with Ce synergistically to promote the formation of the Al11(Ce,La)3 intermetallic phase as predicted by CALculation
