Tag Archives: IGS

Fig. 3. (a) Schematic of four-point reversed bending set-up used in this study. Dimensions in mm. (b) Picture of the bending fatigue test set-up. The specimen was fixed by four fixtures, where two outer fixtures were connected to upper moveable shaft for applying the loading. The two internal fixtures were connected to the fixed base in the bottom. Between the fixture and the shaft/base were thin steel spring to ensure that the specimens can bend flexibly. To show the details more clearly, the distance between each fixture shown in the picture is larger than the actual distances used in this study.

Four-point bending fatigue behavior of rheocast AlSi7Mg0.3 alloy: Role of the surface liquid segregation

By Aluminium-E, Technical Data-E, , , , , , , , ,

Qing Zhang a, Stefan Jonsson b, Anders E.W. Jarfors a aJönköping University, School of Engineering, Materials and Manufacturing, 551 11 Jönköping, SwedenbKTH Royal Institute of Technology, School of Industrial Engineering and Management, Materials Science and Engineering, SE-100 44 Stockholm, Sweden Abstract The surface liquid segregation (SLS) layer in semisolid casting presents higher hardness than the surface of specimens cast using high-pressure die casting

Read More

Fig. 1. Photograph of the project under analysis. View: a) from the fixed half; b) from the mobile halfFig. 2. Thermal images of the mould used in the study: a) fixed half; b) mobile halfFig. 3. The result of an input simulationa)b)a)b)

Effect of Cavitation Phenomenon on the Quality ofHigh-Pressure Aluminium Alloy Castings

By Aluminium-E, Technical Data-E, , , ,

DOI:  https://doi.org/10.7494/jcme.2023.7.3.27 ABSTRACT This article presents an analysis of the effect of cavitation on the erosion of pressure moulds intended for the HPDC casting mould manufacturing process. Changes in the surface area of the eroded areas were investigated via photographs of castings at the beginning of the mould life as well as at 30%. The

Read More

Figure 8(a) Inverse pole figure maps for halite grains with large Kristallbrocken grains labelled 1–5. (b) Pole figures of fine-grained matrix halite excluding five Kristallbrocken grains show no significant crystallographic preferred orientation (CPO). (c) Kernel average misorientation (KAM) map overlaid with white low- and high-angle grain boundaries (misorientation >5∘). KAM map was calculated over a distance of 40 µm (second neighbour) with a threshold of 3∘ in order to enhance the small-angle subgrain boundaries. KAM shows subgrain-free matrix halite with few exceptions in large matrix halite grains, Kristallbrocken 1 and 5 with subgrains, and subgrains in boudin necks of Kristallbrocken 3 and 4. (d) Cumulative reference orientation deviation map over the areas of Kristallbrocken 3 and 4, based on more highly resolved EBSD measurements. Reference points for each of the two grains are indicated. Panels (a) and (b) consist of 30 individual measurements, which due to image distortion under 70∘ tilt cannot be stitched perfectly. Therefore, in some cases an artificial separation of areas belonging to the same grain is visible

Large grain-size-dependent rheology contrasts of halite at low differential stress: evidence from microstructural study of naturally deformed gneissic Zechstein 2 rock salt (Kristallbrockensalz) from the northern Netherlands

By Salt Core-E, Technical Data-E, , , , , , ,

Jessica Barabasch,Joyce Schmatz,Jop Klaver,Alexander Schwedt,and Janos L. Urai Abstract Constitutive laws to predict long-term deformation of solution-mined caverns and radioactive-waste repositories in rock salt play an important role in the energy transition. Much of this deformation is at differential stresses of a few megapascals, while the vast majority of laboratory measurements are at much higher differential

Read More