Category Archives: Technical Data-J

Fig. 2. Microstructure of Al-Si-Mg-Mn and Al-Mg-Si-Mn alloys in the initial state and after chemical modification of eutectic (developed based on: www.alurheinfelden.com)

Al-Mg-Si-Mn合金の微細構造形成と結晶粒微細化

Al-Mg-Si-Mn合金の微細構造形成と結晶粒微細化 高延性Al-Mg-Si-Mn合金のブレークスルー:チタン添加がもたらす強度と延性の二重改善効果とは? 本技術概要は、Viktoriya Boyko氏らによる学術論文

Read More

Fig. 2. Structure of the sand cast alloy(top left) and anodic layer (top right) and structure of the high pressure cast (bottom left) and anodic layer (bottom right) produced on the composite EN-ACAlSi9Cu3

高圧ダイカスト vs. 砂型鋳造:アルマイト処理後のAlSi9Cu3合金の耐摩耗性と硬度を最大化する方法

高圧ダイカスト vs. 砂型鋳造:アルマイト処理後のAlSi9Cu3合金の耐摩耗性と硬度を最大化する方法 本技術概要は、[J. KONIECZNY, K.LABISZ, M. POLOK-RUBINIEC, A. WŁO

Read More

Figure 2 Dependence of die material service life at pressure die casting on pouring temperature

高圧ダイカスト用金型材料:熱疲労、特性、および寿命最大化への道

高圧ダイカスト用金型材料:熱疲労、特性、および寿命最大化への道 金型寿命を最大化する:高圧ダイカスト用金型材料の熱疲労と特性に関する徹底解説 この技術概要は、E. RAGAN、J. DOBRÁNSKY、P. BARON、

Read More

Fig 7. HPDC Machine

Flow pattern analysis of melted aluminum in shot sleeve of pressure dies casting and minimizing the defect

ショットスリーブの欠陥を9割削減?HPDC流動解析が解き明かす最適プロセスの鍵 本技術概要は、Rupesh Kumar Tiwari氏およびTrilok Raj Chauhan氏によって執筆され、Internationa

Read More

Fig. 7 — XRD graphical analysis of the die casting parts Run 5, (b) Run 9, (c) Run 18, (d) Run 20, (e) Run 11 and (f) Run 24

Effects of process parameters on mechanical and metallurgical properties in high pressure die casting of AZ91 magnesium alloy

AZ91マグネシウム合金の高圧ダイカストをマスターする:タグチメソッドによるプロセスパラメータの最適化 この技術概要は、Ali Serdar Vanli氏とAnil Akdogan氏によって執筆され、Indian Jou

Read More

Fig. 5. Simulation of filling a thin-wall casting mould when filled in: (a) 15%; (b) 30%; (c) 50%; (d) 70%; (e) 100%; and (f) in the course of casting solidification

The Effect of a Thin-Wall Casting Mould Cavity Filling Conditions on the Casting Surface Quality

薄肉鋳物の表面品質を脅かす「コールドショット」:鋳造シミュレーションが解き明かす根本原因と対策 本技術概要は、A. Trytek氏らによる学術論文「The Effect of a Thin-Wall Casting Mo

Read More

Fig. 1. Prototype vehicle and the swing arm

Development and optimization of casting technology on part of the suspension of a heavy vehicle used in difficult environmental wetland conditions

論文タイトル シミュレーション主導の鋳造設計:大型車両サスペンション部品の15%軽量化と開発期間短縮を実現 この技術概要は、Marcin Małysza氏らによって執筆され、TRANSACTIONS OF FO

Read More