Technical Resource For Salt Core

Fig. 1. The flowchart of the manufacturing process

Development of Water-Soluble Composite Salt Sand Cores Made by a Hot-Pressed Sintering Process

This introduction paper is based on the paper "Development of Water-Soluble Composite Salt Sand Cores Made by a Hot-Pressed Sintering ...

04/17/2025 / Aluminium-E, aluminum alloy, aluminum alloys, automotive-E, CAD, Die casting, High pressure die casting, High pressure die casting (HPDC), Magnesium alloys, Microstructure, Salt Core, Salt Core-E, STEP, Technical Data-E

Figure 13. Surface of the SA-sample analyzed with the confocal laser scanning microscope. The top images show the sample’s surface before coming into contact with molten salt and the bottom two images show the surface after molten salt contact. Next to the laser images (a,c), the corresponding optical images are displayed (b,d). No significant change in the surface can be seen. The results of the confocal laser scanning microscopy for the other two droplets do not differ qualitatively.

Influence of Salt Support Structures on Material Jetted Aluminum Parts

This introduction paper is based on the paper "Influence of Salt Support Structures on Material Jetted Aluminum Parts" published by ...

04/16/2025 / Aluminium-E, aluminum alloy, automotive-E, CAD, Casting Technique, Die casting, Mechanical Property, Microstructure, Review, Salt Core, Salt Core-E, Technical Data-E, thermophysical properties

Figure 3. Buckling analysis model: boundary condition and load cases.

Experimental and Numerical Study of an Automotive Component Produced with Innovative Ceramic Core in High Pressure Die Casting (HPDC)

This introduction paper is based on the paper "Experimental and Numerical Study of an Automotive Component Produced with Innovative Ceramic ...

Figure 1. Crank case specimen produced with the HPDC process.

Minimizing the casting defects in high-pressure die casting using Taguchi analysis

This introduction paper is based on the paper "Minimizing the casting defects in high-pressure die casting using Taguchi analysis" published ...

Figure 6: Oval form of sea-salt grains (sample No. 5) and EDX analysis of its chemical composition Slika 6: Ovalna oblika zrn morske soli (vzorec {t. 5) in EDX-analiza kemijske sestave

WATER-SOLUBLE CORES – VERIFYING DEVELOPMENT TRENDS

This introduction paper is based on the paper "[WATER-SOLUBLE CORES – VERIFYING DEVELOPMENT TRENDS]" published by "[Materiali in tehnologije / ...

04/14/2025 / Applications, automotive-E, CAD, Die casting, Salt Core, Salt Core-E, Technical Data-E

Fig. 7 The scanning electron microscope (SEM) images of solidified structure. (a) and (b) : NaCl–10 mol%Na2CO3. (c) and (d) : NaCl– 70 mol%Na2CO3.

Strength of Salt Core Composed of Alkali Carbonate and Alkali Chloride Mixtures Made by Casting Technique

This introduction paper is based on the paper "Strength of Salt Core Composed of Alkali Carbonate and Alkali Chloride Mixtures ...

04/02/2025 / aluminum alloys, ANOVA, CAD, Casting Technique, Copper-E, Die casting, High pressure die casting, High pressure die casting (HPDC), Microstructure, Permanent mold casting, Salt Core, Salt Core-E, Technical Data-E, 솔트 코어

Figure 4. 3D scheme of the rolling process and 2D simplification in the FE simulation.

Double-Sided Surface Structures with Undercuts on Cold-Rolled Steel Sheets for Interlocking in Hybrid Components

This introduction paper is based on the paper "Double-Sided Surface Structures with Undercuts on Cold-Rolled Steel Sheets for Interlocking in ...

03/28/2025 / Aluminium-E, Applications, CAD, Die casting, Electric vehicles, High pressure die casting, Review, Salt Core-E, Sand casting, STEP, Technical Data-E

Abbildung 4.1: Darstellung der Biegestab-, Gießspiralen- und Zugstabkokille für die Salzkernprinzipuntersuchungen

Cavity and Composite Casting of Die Casting Components – Numerical Design Methods and Experimental Verification

This introductory paper is the research content of the paper "Hohl- und Verbundguss von Druckgussbauteilen – Numerische Auslegungsmethoden und experimentelle ...

03/18/2025 / Aluminium-E, Aluminum Casting, automotive-E, CAD, Casting Technique, Die casting, FLOW-3D, High pressure die casting, High pressure die casting (HPDC), IGES, Microstructure, Quality Control, Salt Core, Salt Core-E

Figure 3. Schematic drawing of the designated tee-joint (K0), the core (K1), the shell model (K2), and skin layer model (K3).

A Water-Soluble Core for Manufacturing Hollow Injection-Molded Products

This article introduces the paper 'A Water-Soluble Core for Manufacturing Hollow Injection-Molded Products' published by 'MDPI'. 1. Overview: Title: A ...

03/11/2025 / Aluminium-E, ANOVA, Applications, CAD, CFD, Die casting, Salt Core, Salt Core-E, STEP, Taguchi method, Technical Data-E

Figure 5 maps the four composition areas (A, B, C, D) predicted to have high strength based on deflection mechanism and factors reducing strength.

Bending Strength of Salt Core Comprised of KCI-NaCl-Na2CO3-K2CO3 Systems

This article introduces the paper ['Bending Strength of Salt Core Comprised of KCI-NaCl-Na2CO3-K2CO3 Systems'] published by ['The Japan Foundry Engineering ...

03/07/2025 / Aluminium-E, aluminum alloy, Applications, AUTOMOTIVE Parts, CAD, Die casting, Microstructure, Salt Core, Salt Core-E

Figure 3. The qualitative electron probe micro-analysis (EPMA) maps of Si and Mg segregation in three different casting conditions. The EPMA maps are purposefully enhanced to reveal the minor segregation bands. The line scans are indicated with white dashed lines. The concentration (at.%) vs distance (μm) plots correspond to the respective line scans in the EPMA maps.

Solute micro-segregation profile and associated precipitation in cast Al-Mg-Si alloy

This article introduces the paper ['Solute micro-segregation profile and associated precipitation in cast Al-Mg-Si alloy'] presented at the ['Philosophical Magazine'] ...